PLUG & PLAY – NO TOOLS NEEDED
Say Goodbye to Ice!
Whether you're just starting with cold therapy or you're a seasoned expert, you likely value the benefits of cold exposure over the effort required to maintain it with ice. Let's be honest – keeping enough ice on hand for a cold bath can be quite a hassle. Our chiller takes the effort out of the equation, keeping your ice bath perfectly cold and even allowing you to skip the ice altogether. This means you'll use your cold therapy tub more consistently and frequently, enjoying the benefits without the extra work.
The 3/4 HP water chiller can reach temperatures as low as the low 40°F range, and under the right conditions, it can even drop into the high 30°F range. The biggest factors affecting the temperature of your cold therapy tub are ambient temperatures and sun exposure (your body heat is minimal by comparison). By minimizing these external heat sources, you can improve the performance of the chiller. Achieving low to mid-40°F temperatures is possible even in full sun or less than ideal conditions.
Please Note: Ensure your setup is in an area that can handle wetness, moisture, and condensation.
Bundle includes:
- 100gal insulated tub 54″ x 31″ x 32″ external / 43.5″ x 24.5″ x 24″
- Attached filter canister with 150 micron washable / reusable filter
- Inline Screen – coarse filter to catch hair and large debris prior to chiller
- 3/4HP Cold Therapy Chiller with built in pump
- Quick connect hoses
We do not recommend putting the chiller in an area that cannot get wet as the chiller, along with the tubing, will produce condensation.
If you ever notice your system does not have flow, or if you are questioning whether the flow you’re seeing is normal, immediately unplug the chiller & contact betterliving@regenbodylab.com
In any application that requires a water chiller, strong flow is crucial. If you have some flow throughout the system, but not enough, water will freeze inside of the chiller.
Damage caused by slow flow throughout the system due to improper setup or maintenance will not be covered under the manufacturer warranty.
Cost to Run (lower than most expect):
At $0.12/KWh the monthly cost of operation should be around $15-$25/month. The compressor and fan only turn on when cooling is needed, once the water reaches your set point they turn off and only the low wattage pump continues to run.
A common question we get revolves around setting the chiller up on a timer. Ideally, you’ll want to keep the water cold at all times. There are a few reasons for this –
- Cold water keeps bacteria (slimy walls) largely under control by slowing or stopping their growth. This significantly reduces the amount of maintenance needed to keep your water clean for longer periods of time. This means less frequent water changes and that much lower levels of sanitizer being an effective doses (chlorine/hydrogen peroxide/etc).
- If you are using it on a regular basis the amount of potential power savings will be fairly insignificant, the heat it would gain in the “off” period still needs to be removed when you turn it back on. So, if running is normally cost $18-$28/month you might be able to save $1-$3/month. However, you will have to change water and the filter more often, so it is unlikely to be a net cost savings.
- When you cut power to the chiller you also cut power to the pump. Pumps get the most wear and tear during startup, that’s when a pump is most likely to fail as well. Cycling the power to the chiller is just adding unnecessary wear and tear to the pump.
Chiller Specs:
- 3/4HP High Efficiency Chiller
- 65 dBA
- 110 – 120 Volts / 450 Watts / 3.9 Amps
- 14”W x 20”D x 12”H
- 52 Pounds
- Built in Pump
- 10′ power cord with GFCI protection
- Rain Proof* (*disconnect chiller and drain completely when ambient temps are freezing or below to prevent damage to chiller)
- 1 Year Product Warranty
- Proudly made in the USA
